Asymtek TC V3 Spezifikationen

Conformal Curing Oven TC V3 Maintenance Manual P/N 7211568

2-2 Safety Basic Safety Precautions and Practices The following precautions and practices are recommended during Cure Module operation and maintenanc

Safety 2-3 Earthquake Precautions In the event of an earthquake, the cure module must be secured to prevent movement that could cause injury to perso

2-4 Safety 4. Reset the main circuit breaker inside the electronics enclosure if it has been tripped. 5. Turn the red EMO button clockwise until it

Safety 2-5 Lockout of Electrical Energy TC V3 Cure Module electrical components have been designed in accordance with industry-wide safety standards.

Maintenance 3-1 3 Maintenance Overview Performing the recommended maintenance and service procedures increases the life of your Cure module and ens

3-2 Maintenance Preventive Maintenance Table 3-1 Preventive Maintenance Recommended Frequency Maintenance Procedure Instructions WEEKLY – 120 h o

Maintenance 3-3 Maintenance Procedures CAUTION!Safety Maintenance procedures should only be performed by trained service technicians. Refer to the

3-4 Maintenance Conveyor Incremental Encoder Adjustment The Conveyor Incremental Encoder returns an accurate measurement of conveyor speed to the PLC

Maintenance 3-5 Conveyor Chain Tension Adjustment To adjust the tension of the conveyor chains: 1. Turn the power off by moving the Main Switch to t

3-6 Maintenance Transmission Chain Tension Adjustment To adjust the tension of the transmission chain: 1. Turn the power off by moving the Main Swit

Maintenance 3-7 Adjustment of the Rail Parallelism If a printed circuit board (PCB) falls down into the oven, the conveyor rail needs adjustment. To

3-8 Maintenance 5. If the input and output measurements are not equal, remove the access cover located under the crank to access the transmission ge

Maintenance 3-9 Figure 3-10 Output Rail 8. If the three measurements are not equal, remove the screws from the rail fixation and adjust the posit

3-10 Maintenance Thermocouple Replacement To replace a thermocouple: 1. Turn the power off by moving the Main Switch to the OFF position. 2. Open

Maintenance 3-11 Resistor Replacement To replace the top resistor: CAUTION!1. Turn the power off by moving the Main Switch to the OFF position. B

3-12 Maintenance 6. Unscrew the retaining nut on the cable. Figure 3-15 Stuffing Box Figure 3-16 Joint 7. Unscrew the nut on the stuffing box

Maintenance 3-13 13. Replace the top access cover. 14. Close the hood using proper procedures described in “Hood Opening/Closing Operation” of the

3-14 Maintenance 11. Re-attach the clips on the maintenance part. 12. Check to make sure the new resistor is positioned in line with the glass. 13.

Maintenance 3-15 Adjustment of the Dropped Board Detection Cell (optional) To adjust the dropped board detection cell: 1. Turn the power on by movin

P/N 7211568, Revision C English Translation based on French P/N 7211572, Rev. B ©2010 NOTICE This is a Nordson ASYMTEK publication, which is protect

3-16 Maintenance Auto-Tune Procedure The purpose of the auto-tune is to set PID parameters of temperature control loops. This function is used only i

Maintenance 3-17 3. Click on a graphical visualization of a zone (Figure 3-29). Figure 3-29 Graphic Visualization of a Zone 4. Apply the values

Troubleshooting 4-1 4 Troubleshooting Overview Troubleshooting helps you identify common problems that you may experience with your cure module and

4-2 Troubleshooting Alarms / Trouble Possible Causes Verifications and Actions Alarm Conveyor 2 – Speed Band Alarm Speed Sensor defective Check th

Troubleshooting 4-3 Alarms / Trouble Possible Causes Verifications and Actions Board Jam Alarm Photo cell defective Adjust the sensor (refer to the

Parts List 5-1 5 Parts List This section contains parts ordering information for the TC V3 Conformal Curing Oven. Part number information is also a

5-2 Parts List Level 3 - Long Lead-Time Parts Figure 5-3 Parts with a long procurement lead-time or for software update. Designation Reference Ma

P/N 7211568 Revision C ©2010 Nordson ASYMTEK Headquarters 2762 Loker Avenue West Carlsbad, CA 92010-6603 USA Tel: (760)

Table of Contents i Table of Contents 1 Introduction ...

ii Table of Contents Table of Figures Figure 3-1 Torque Limiter Adjustment ...

Introduction 1-1 1 Introduction Overview This manual covers maintenance procedures necessary for the preventive and corrective maintenance of the T

Safety 2-1 2 Safety Overview Operation of the TC V3 Conformal Curing Oven involves heat, electrical power, mechanical devices, and the use of hazar